NEIEP Advanced Topics In Elevators (800) Practice Test

These questions are part of the practice quiz. Start practicing

• What is "frequency modulation" in the context of elevator drives?
• What is a common disadvantage of hydraulic elevators compared to traction elevators?
• What height limitation is specified for anti-slide devices in the elevator industry?
• What type of shackle is the most commonly used in rigging?
• What is the role of the elevator's detectors?
• What is the maximum distance a LULA car door switch can operate from being fully closed?
• What is the maximum rise acceptable for a LULA elevator?
• Which device allows you to lower a hydraulic elevator manually in the event of a power failure?
• What is the maximum platform area allowed for residential elevators?
• What is the purpose of fire service operation in elevators?
• What is the purpose of a machine room in an elevator system?
• With a wye-delta starter, what does it eliminate the need for during reduced current starting?
• What is the main advantage of wye-delta starting in electrical systems?
• The handrail height for a residential platform lift must be between __________ to __________ inches above the stair tread nosing.
• Which type of door system is most commonly used in modern passenger elevators?
• Which assembly supports the platform of a hydraulic elevator?
• What is the purpose of a "raptor" in elevator systems?
• In a hydraulic system, what does pressure equal?
• Which of the following methods is recommended to prevent cylinder warping during welding?
• What kind of tests are performed on elevators during installation?
• What is the maximum capacity typically allowed for passenger elevators?
• What does "dynamic balancing" refer to in elevator systems?
• What does the "safety factor" analyze in elevator ratings?
• What condition would cause a Ground Fault Circuit Interrupter (GFCI) to trip?
• What is the primary function of an elevator controller?
• For a residential platform lift, the governor shall set at a maximum speed of __________.
• Why is it necessary to run a ground wire to the car sling of a hydraulic elevator?
• How should the silencer/muffler be positioned in relation to the pump?
• How is the maximum allowable rise for a LULA defined according to code?
• Changes in the viscosity of the oil in a hydraulic elevator mainly affect which two operations of the elevator?
• What is the maximum rise for a LULA elevator?
• How close to fully closed must car door switches operate?
• When utilizing belt-driven pumps, what is a common advantage?
• A dogleg in elevator installation can occur due to:
• What is the primary risk associated with not barricading wellways properly?
• Which of the following statements is correct regarding the maintenance of a hydraulic elevator?
• What does a Ground Fault Circuit Interrupter (GFCI) do?
• If the diameter of the plunger in a hydraulic elevator system is reduced while keeping other elements constant, what happens to the system pressure?
• What is the significance of "vibration isolation" in elevators?
• What is the maximum allowable speed for a chairlift in feet per minute?
• What is the main purpose of the NEIEP Advanced Topics in Elevators (800) Practice Test?
• Which regulations usually govern elevator installation and inspection?
• What is a "bypass switch" used for in elevator systems?
• What is the difference between a geared and a gearless traction elevator?
• How do elevators use "control algorithms"?
• What is the maximum platform area for a residential elevator?
• What safety mechanism prevents the elevator car from falling?
• In hydro elevators, where is the load primarily carried?
• How is elevator capacity typically calculated?
• What is the impact of "door reopening devices" in an elevator?
• What is the typical spacing range for tower wall ties?
• What type of switch is designed to prevent sagging steps in elevators?
• What is the maximum angle of inclination for moving walks?
• When using a beam clamp, what is the maximum recommended load for the lower flange as a percentage of the full load capacity?
• True or False: LULA's must have a permanent mechanical holding device to stop the car within a specific height range above the pit floor.
• In terms of safety, why is it important for elevators to have a leveling system?
• What is the primary function of a relief valve in an elevator system?
• What is the maximum rated load for a one-seat chairlift?
• What is the capacity limit for two persons on a chairlift?
• What is the maximum load for a two-seat chairlift?
• What ecological benefits do regenerative drives provide in elevators?
• True or False: Codes require platform lifts to have a handrail that is between 1 and 3 inches in diameter.
• What is the minimum distance a handrail must be from the wall for platform lifts?
• Hydraulic overspeed valves activate if a downward traveling car exceeds what speed percentage range?
• How does an oil hydraulic elevator operate?
• Which technology is used to improve elevator efficiency in modern systems?
• True or False: The speed governor switch on moving walks directly connected to the driving machine must be manually resettable after it activates.
• What information do digital displays provide in modern elevators?
• What is the minimum free passage width required on a stairway when installing chairlifts?
• In relation to platform lifts, what does the term 'runway' refer to?
• What does the term "pit" refer to in elevator construction?
• What is the effect of increasing the size of the oil line in a hydraulic elevator system while keeping other elements constant?
• How much sagging does a step level switch prevent?
• What is the maximum allowable gap between skirt panels and adjacent step treads on an escalator?
• True or False: The comb segment teeth are required to remain at the same level as the treadway surface for operational safety.
• What aspect of elevator performance does a full-load test evaluate?
• Which item is critical for ensuring the longevity of elevator cables?
• What is the maximum angle of inclination for moving walks within a specific distance from the entrance or exits according to code?
• What does the term "full-load test" signify in elevator systems?
• What does "NFPA" represent in the context of elevator safety regulations?
• What type of elevator system uses a counterweight?
• What is the purpose of properly barricading wellways in an elevator maintenance area?
• Per code, what is the maximum speed at which the safety mechanism must be set when activated by a governor?
• What is required for LULA elevators in terms of mechanical holding above the pit floor?
• How does a "dual-purpose" elevator differ from traditional elevators?
• What is the best rigging equipment to control horizontal movement of an escalator during installation?
• At what percentage of the rated speed must the overspeed valve of a hydraulic LULA stop the car?
• What does NEIEP stand for?
• How are rack sections for rack and pinion hoists aligned?
• How many kilograms is equivalent to 1 pound?
• What type of machine room is required for hydro elevators in low-rise applications?
• What is the common maximum speed for rack and pinion hoists?
• Is the pressure relief valve operated electronically?
• Why is it crucial to conduct regular inspections of elevator cables?
• What is a key benefit of implementing smart technology in elevators?
• In a hydraulic system, what does area equal?
• What can be done to prevent rusting of the plunger if the jack unit is installed in the well hole before elevator completion?
• What is the main reason for utilizing anti-slide devices in elevator construction?
• How high must barricades around the wellway be, according to safety regulations?
• What is typically used to verify that the drill hole is vertical?
• What position must the comb segment teeth be in relation to the upper surface of the treadway?
• If a step of an escalator drops more than 1/8", what is the expected outcome?
• At what speeds should temporary run buttons operate the platform and sling?
• What role does a "load sensor" play in an elevator system?
• In what situation would an elevator likely require a "redesign"?
• How frequently are routine tests and inspections required for LULA's in non-residential buildings?
• What is "hoisting" in elevator terminology?
• What is a common maintenance requirement for elevators?
• In the context of elevators, what is "system redundancy"?
• What is the main advantage of using machine-room-less (MRL) elevators?
• In elevator terminology, what does the term "hoistway" refer to?
• What happens to the flow rate if the oil line diameter is reduced in a hydraulic elevator system?
• What we would normally refer to as a hoistway or hatchway in elevator terms is called a __________ when discussing platform lifts.
• What primary factor does the design of an elevator’s safety system emphasize?
• What is an important consideration when designing an elevator system for a building?
• Which type of valve allows an elevator car to be lowered in the event of a power failure?
• Which organization sets the standards and regulations for elevator safety?
• Which component is crucial for detecting obstructions in the elevator's path?
• What kind of communication system is essential in modern elevators for emergency situations?
• What is the typical lifespan of an elevator system?
• What is a major benefit of regular elevator maintenance?
• Routine periodic tests and inspections are to be made at intervals no longer than __________ for LULA's in buildings other than private residences.
• If a hydraulic elevator trips its low oil timer and the oil level is good, what should be checked?
• To plumb the jack hole correctly, where should the spider bob be attached from?
• Which device is used to check the plumb of the jack hole during drilling?
• What is an "emergency brake system" in elevators designed to do?
• What device is typically used to maintain proper tension on the treadway belt in belted walkways?
• ANSI A10.4 may be used for a Rack and Pinion installation when it is used as a what?
• What effect does temperature have on oil used in elevator systems?
• What do "refurbishments" in elevators refer to?
• What are "back-up power systems" used for in elevators?
• Combplate teeth must be set to ensure they are below the what surface?
• What is the function of a "safety switch" in elevators?
• What is the maximum distance allowed between anti-slide devices on an escalator?
• What force must barricades be able to withstand according to safety standards?
• What safety feature is designed to ensure elevators are not overloaded?
• Which component is typically responsible for controlling the speed of an elevator?
• What is the primary purpose of an elevator's leveling system?
• Submersible pumps are always:
• What major advantage does a hydraulic elevator have regarding building design?
• What type of brake is typically used in modern elevators for safety?
• What height measurements are crucial for LULA operation safety?
• True or False: The frame of a Rack and Pinion elevator is similar to a traditional elevator car sling.
• What is the function of a "door operator" in an elevator?
• What tool is used to check a jack hole for plumb?
• Which speed limit is specified for chairlifts along their incline?
• Which type of elevator is most commonly used for high-rise buildings?
• What is the purpose of a silencer/muffler in hydro elevator systems?
• What materials are commonly used for elevator ropes?
• Which of the following is a feature of energy-efficient elevators?
• Why is ongoing training crucial for elevator technicians?
• The speed as measured along the incline of a chairlift shall not exceed __________.
• Which of the following features is typically found in a modern elevator control system?
• What is a "smoke shaft" used for in an elevator safety context?
• What component is used to cushion pulsations in the oil caused by the pump in a hydraulic elevator?
• What component prevents the plunger from leaving the cylinder?
• Which of the following describes the inclination angle for moving walks that shall not exceed a certain limit as specified by code?
• What does "phase sequence" refer to in three-phase elevator systems?
• A non-removable means must be provided to prevent a LULA's car downward movement at a height of ___________ to __________ inches above the pit floor.
• What is the operating pressure of a hydraulic elevator with a gross weight of 1500 pounds and a plunger area of 15 square inches?
• Which of the following components is essential for the safe operation of an elevator?
• What equipment is recommended for horizontally pulling a truss during installation?
• In a hydraulic elevator system, what is the main function of the pressure relief valve?
• What do "safety margins" ensure in elevator design?
• What is the role of vibration dampeners in elevators?
• What is the primary purpose of a governor in a residential platform lift?
• When welding, how far apart should tack welds be shifted?
• Which type of elevators may have lower construction costs due to their loading mechanism?
• What role does the governor play in an elevator system?
• On power units with the motor beneath the tank, which type of pump coupling may be used?
• How often should inspections be conducted for LULA's in private residences?
• How many cubic inches are in one gallon?
• What occurs if a hydraulic elevator's plunger is too small for its intended load?
• Why is it important to follow a welding procedure using short welds on opposite sides of the cylinder?
• What type of spiral is classified as a short radius spiral in chairlifts?
• According to elevator safety standards, how far apart must anti-slide devices be spaced?
• What standards do crew members typically need to follow during elevator inspections?
• What is the maximum angle of inclination allowed for installation at a site?
• What is the allowable interval for inspections of LULA's in private residences?
• The car must run at which speed when using temporary run buttons?
• What is the primary role of a "control panel" in elevators?
• How much tension is generally maintained on the treadway belt of belted walkways?
• How do servos function in elevator operation?
• Which component is primarily responsible for controlling elevator speed?
• In what context is a "runway" term used when discussing platform lifts?
• What is the least amount of free passage width required on the stairway for a chairlift?
• When welding a joint, how many tack welds should be placed 180 degrees apart?
• Where is the tensioning device located in a belted moving walkway?
• How many pounds are there in 2000 kilograms?
• What component is fastened to the platen plate in the bolster assembly?
• Moving walk overspeed switches must activate at no more than what percentage of the rated speed?
• How do modern elevators typically manage predictive maintenance?
• Which of the following is not considered a performance indicator for elevators?
• What is "load-weighing" technology in elevators?
• What is the minimum height requirement for a barricade around an open wellway?
• What is the most common cause of elevator accidents?
• By how many degrees can an installed escalator exceed the code's specified angle of inclination?
• What is the setback distance for the outer edge of a deck requiring anti-slide devices?
• How does the hydraulic system maintain consistent pressure?